حداقل ترام در چاپ فلکسو چیست؟حداقل ترام در چاپ فلکسو یعنی کوچکترین ترامی که در کلیشه شما قابلچاپ است چه درصدی میباشد.
در کلیشههای چاپ فلکسو از دو جهت میتوان حداقل ترام را بررسی کرد. اول حداقل ترامی که کلیشهساز میتواند بر روی کلیشه تولید کند و دوم حداقل ترامی که چاپخانه شما میتواند چاپ کند.
حداقل ترام در حالت اول که مربوط به کلیشه سازی است به روش و دستگاههای کلیشهسازی برمیگردد. بهطور مثال در روش آنالوگ از فیلم لیتوگرافی استفاده میشود ترامهای زیر ۳ درصد خیلی راحت قابلتولید نیستند. پس در مرحله نوردهی و کلیشهسازی هم انتقال آنها بر روی کلیشه میتواند مشکلاتی داشته باشد.
در روش دیجیتال تولید ترامهای ریز خیلی راحتتر از روش آنالوگ است و بهراحتی با داشتن دستگاههای مدرن امروزی حتی ترامهای کمتر از ۱ درصد نیز بر روی کلیشه قابلتولید است. بهطور مثال حتی ترام ۰٫۴ درصد نیز بر روی کلیشه ۱٫۱۴ قابلتولید است. البته چاپ شدن و باقی ماندن این ترام ریز بر روی کلیشه در طول چاپ مسئله دیگری است.
حداقل ترام در حالت دوم به چاپخانه برمیگردد. وقتی چاپخانه ای به کلیشه ساز سفارش تولید کلیشه میدهد باید برای ترامهای کار الپیای مشخص کند. این الپیای رابطه خاصی با حداقل ترام قابلچاپ در چاپخانه دارد. اگر رابطه بین الپیای کلیشه و الپیای آنیلوکس مصرفی در چاپ درست رعایت نشده باشد و ترامهای پایین روی کلیشه کوچکتر از حفرههای روی آنیلوکس باشند نوک ترامها وارد حفرههای روی آنیلوکس میشوند و مرکب اضافی به خود میگیرند و باعث دون زدن چاپ میشوند.
اگر یک کار چاپی رو در نواحی هایلایت یا روشن آنکه ترامهای درصد پایین دارد با دقت نگاه کنید متوجه میشوید که در بعضی از نواحی بعضی از ترامها بزرگتر و بینظمتر از بقیه ترامها هستند. در چاپ فلکسو به این مشکل داتدیپینگ و یا وارد شدن نوک ترام به حفره آنیلوکس گفته میشود که باعث کثیف شدن چاپ میشود.
این فرمول به این معنی است که اگر کلیشهای را سفارش میدهید باید الپیای بالاترین آنیلوکسی که برای چاپ تصاویرتان در نظر گرفتهاید را تقسیمبر ۶ کنید و عدد بهدستآمده را برای الپیای کلیشه خود استفاده کنید. البته من پیشنهاد میکنم کمی پایینتر از آن را سفارش دهید.
البته در این کار باید دقت کنید که حتماً از عدد الپیای آنیلوکس استفاده کنید چون بر روی بعضی از آنیلوکسها عددی که نوشته است عدد الپیسی آن است و برای به دست آوردن الپیای آن، باید در ۲٫۵۴ ضربش کنید.
What is the minimum tram in flexo printing? What is the minimum tram in flexo printing, which is the smallest tram that can be printed in your stereotype?
In flexo printing stereotypes, the minimum tram can be checked in two ways. The first is the minimum amount that the stencil maker can produce on the stencil and the second is the minimum amount that your printer can print.
The minimum tram in the first case, which is related to stereotyping, goes back to stereotyping methods and devices. For example, the analog method uses lithographic film. Trams below 3% are not very easy to produce. So in the stage of exposure and stereotyping, their transfer to the stereotype can have problems.
In the digital method, the production of small trams is much easier than the analog method, and with modern devices, even trams less than 1% can be easily produced on the stereotype. For example, even a 0.4% tram can be produced on a 1.14 stencil. Of course, printing and keeping this small tram on the stencil during printing is another matter.
At least the tram returns to the printing house in the second case. When a printing press orders a stereotype maker, it must specify an ellipse for the work trams. This ellipse has a special relationship with the minimum printable tram in the printing house. If the relationship between the stencil pins and the anilox pins used in the correct printing is not observed and the trams below the stencil are smaller than the holes on the anilox, the tram tips will enter the holes on the anilox and take up the extra ink and cause the print to drop.
If you look closely at a print job in high-light areas that have low percentage trams, you will notice that in some areas some trams are larger and more irregular than others. In flexo printing, this problem is called dot-doping or the tip of the tram entering the anilox cavity, which causes the printing to become dirty.
This formula means that if you order a stereotype, you have to divide the highest anilox screens you want to print your images by 6 and use the resulting number for your stereotype screens. Of course, I suggest ordering a little lower than that.
Of course, in this work, you must be careful to use the number of anilox olpines, because on some aniloxes, the number he wrote is the opium number, and to get its olpics, you have to multiply it by 2.54.
طراحی بسته بندی #لوگو #آرم #شیر #طراحی و چاپ کارت ویزیت
طراحی بسته بندی #لوگو #آرم #شیر #طراحی و چاپ کارت ویزیت #شیر کاِکائو
the ,in ,tram ,and ,to ,printing ,the minimum ,is the ,in the ,بر روی ,روی کلیشه
درباره این سایت